2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install

Upgrade 2005-2012 Ford Mustang Stock Halogen headlight bulb with all new LED bulbs

How to install LED headlight Ford Mustang 2007
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 1

Do you have a 2005-2012 Ford Mustang and noticed the low amount of light when using your halogen headlight bulbs? Maybe you always find yourself struggling to see in front of you at night or struggle to see though the rain and fog.

How about trying to drive in severe weather conditions and almost hitting that person you “did not” see?” Using those dingy halogen headlight bulbs in your vehicle can do that to your vision therefore ALLA Lighting is here to help! Upgrading your old halogen bulbs of your Ford Mustang to new aftermarket LED bulbs can add a great new look to your vehicle as well as enhance visibility at night for safer driving experience.  It will help to enhance much more visibility at night driving, also make your vehicle more luxury and easier noticed by other drivers. It will make your driving smarter, safer, brighter and better.

When choosing to upgrade your old halogen bulbs to new LED bulbs, it is highly recommended to confirm you have the correct LED replacement bulbs. To confirm LED bulb size, always refer to original halogen bulb size via stock bulbs from your Ford Mustang directly

The Following Information shows step by step installation instructions on 

How to install a ALLA Lighting H13 LED replacement bulb

Compatible Vehicles: 2005-2012 Ford Mustang

Tools Needed for Installation: Drill

Step #1

Take off the air filter intake by removing the 10mm bolt 
* Using Drill*
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 2

Step #2

Push down the clip and pull out directly.
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 3

Step #3

Twist counter clockwise to remove  the stock halogen bulb
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 4

Step #4

Make sure not to leave the rubber ring/ gasket in the housing if it sticks
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 5

Step #5

Connect the vehicle harness connector to the LED driver/LED plug connector
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 6

Step #6

Align the locking tabs, insert the new LED bulb and twist clockwise to lock it in the housing.
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 7

Step #7

Make sure the bulb is installed vertically and the LED chips are facing left and right. Pigtail pointing 6 or 12 o’clock has been installed vertically with perfect beam angel. If not in correct position, most models are beam adjustable and can adjust the beam position.
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 8
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 9

Step #8

Pro Tip: Use zip ties to secure driver 
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 10

Step #9

Put the air filter intake back
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 11

Sep # 10

Now repeat the same steps on the passenger side.
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 12
Correct position of Low and High beam

Low beam LED chip should be in upper position and High beam LED chip should be in lower position. 

LED chips should be facing Left to Right (side to side)

2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 13
Low beam and High beam once installed correctly
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 14
2005-2012 Ford Mustang Headlight Upgrade LED Installation How to Install 15
Check out our Step by Step installation video! 

Congratulations!! Your installation is now complete in your 2005-2012 Ford Mustang headlight bulb upgrade. If you experienced any issues during your installation and unable to complete installation, please contact us for assistance. If the  LED bulbs are experiencing hyper-flashing, flickering, an error code issues, then load resistors for this application will be required to be installed. These issues occur due to the LEDs low current nature which draws much less current than original stock halogen bulbs.

Please feel free to contact us at service@allalighting.com for assistance. Our team of highly trained representatives will be available to assist and provide best solution. May also visit us at www.allalighting.com 

Looking for more LED upgrades for your vehicle. Check out the below bulb guide!  For your reference only. All information below is not 100% guaranteed accurate. Please check original halogen bulb size before purchasing.

Vehicle Information Exterior Lights

Low and High Beam: Stock Bulb size # H13

Fog Light: Stock Bulb size # : H11/9008

Front Turn Signal Light: Stock Bulb size # :  3457Nak/3457K/3156K

Front Side Marker Light: Stock Bulb size # : 194

Parking Light Bulb: Stock Bulb size # : 3457NAK/3457K/3156K

Inner and Outer Turn Light: Stock Bulb size #N/A : stock LED Not serviceable by Owner

Inner and Outer Brake Light: Stock Bulb size #N/A : stock LED : Not serviceable by Owner

Inner and Outer Tail Light: Stock Bulb size #N/A : stock LED : Not serviceable by Owner

Back-Up Reverse Light: Stock Bulb size # : 912

Center High Mount/ 3rd Brake Light: Stock Bulb size #N/A : stock LED : Not serviceable by Owner

License Plate Light:  Stock Bulb size # : 6418

Vehicle Information Interior Lights

Interior Dome Light:  Stock Bulb size # : W5W

Interior Map Light:  Stock Bulb size # : W5W

Trunk/Cargo Light:  Stock Bulb size # : 211-2 

Interior Door Light Bulb: Stock Bulb size # : W5W

Instrument Panel Light Bulb: Stock Bulb size # : PC195

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: