Table of Contents
How to Install 2018-2022 Jeep Compass Map Lights Bulbs
Ready to upgrade your old halogen bulbs? Learn how to replace and complete the installation for LED light bulbs. Easy installation and tips!
The halogen interior bulbs may be too dim in your 2018-2022 Jeep Compass, which can make vision difficult, especially in bad weather or severe driving conditions. Upgrading the old halogen bulbs on your 2018-2022 Jeep Compass with new aftermarket LED bulbs can add a great new look to your vehicle and improve visibility at night for a safer driving experience.
If you choose to upgrade your old halogen bulbs to new LED bulbs, it is best to confirm you have the correct replacement LED bulb by referring to the original bulb or the vehicle’s direct owner’s manual. We will show you how to install your new ALLA Lighting LED bulbs for your Map Lights Bulbs.
Bulb sizes for the 2018-2022 Jeep Compass Map Lights Bulbs is # 168
The following information is step-by-step instructions on how to install your new LED T10 Wedge 168 194 LED Bulbs Interior Lights Replacement
For this installation, you’ll need:
- Curved trim puller tool.
Step #1
Begin in the map lights of your 2018-2022 Jeep Compass.
Step #2
Slide the trim tool into the edge of the light housing and pry the clips free.
Step #3
There are two more clips closest to the windshield.
Step #4
Pull the housing away from the windshield to remove it.
Step #5
You can see how the rear clips fit into the slots and the front clips hang on the light housing.
Step #6
Remove the map light socket by tipping the socket towards the front.
Step #7
Pull the incandescent bulb from the socket
Step #8
Replace with the LED and test it
Step #9
Replace the socket back into the housing.
Step #10
Now repeat the same steps for the driver side map light.
Step #11
Remove the socket and pull out the incandescent bulb.
Step #12
Replace with the LED bulb and test it.
Step #13
Push the socket back into the housing.
Step #14
Line up the clips near the windshield and push the housing onto the clips.
Step #15
Lift the back side of the housing up until the clips lock in place.
Check out our Step by Step installation video!
Congratulations! Your LED Map Lights Bulbs Installation is now complete in your 2018-2022 Jeep Compass. If you experienced any issues during your installation and unable to complete installation, please contact us for assistance. If the LED bulbs are experiencing hyper-flashing, flickering, an error code issues, then load resistors for this application will be required to be installed. These issues can occur due to the LEDs low current nature, which draws much less current than original stock halogen bulbs.
Please feel free to contact us at service@allalighting.com for assistance. Our team of highly trained representatives will be available to assist and provide the best solution. May also visit us at www.allalighting.com
Looking for more LED upgrades for your 2018-2022 Jeep Compass? Check out the below bulb guide! For your reference only. All information below is not 100% guaranteed accurate. Please confirm the original bulb part numbers by referring to the original bulb or the vehicle’s direct owner’s manual prior to purchase
Vehicle Information
Front Exterior Lights
Low Beam Headlight Bulb: Stock #: H11 (H11A)
High Beam Headlight Bulb: Stock #: 9005 (HB3)
High Beam and Low Beam with HID Headlamps: Stock #: HID-D3S
Front Fog Light Bulb: Stock #: H11 (H11A)
Daytime Running Light: Stock #: 2504
Front Turn Signal Light: Stock #: 7443
Rear Exterior Lights
Back Up Light Bulb: Stock #: 7440
Rear Turn Signal Light Bulb: Stock #: 7440, 7443.
Brake Light Bulb. Stock #: 7443, LED
Tail Light Bulb. Stock #: 7443, LED
Interior Lights
Map Light Bulb: Stock #: 168
Dome Light Bulb: Stock #: 6418
Luggage Compartment Light Bulb: Stock #: 6418
Vanity Mirror Light Bulb: Stock #: 6418